FYSETC-E4 esphome roller blinds

esphome.yaml

substitutions:
  device_name: "lush-cover-controller"
  pulley_diameter_mm: "21.963"
  gear_ratio: "1880/2000"
  distance_mm: "2050"
  acceleration: 500 steps/s^2
  velocity: 2500 steps/s # 200 (motor steps) * ${microsteps}
  back_off_steps: "200" # back off some steps to reduce stepper energize noise

  open_current_x: 1000ma
  open_stall_threshold_x: "28"
  close_current_x: 300ma
  close_stall_threshold_x: "30"
  tcool_threshold_x: "1000"
  change_direction_x: "True"
  tmc_address_x: "0x01"

  sense_resistor: "0.15"

external_components:
  source: github://lumascet/esphome@stepper-tmc2209-new_uart
  components: [uart, tmc2209]

esphome:
  name: ${device_name}
  platform: ESP32
  board: nodemcu-32s
  platformio_options:
    upload_speed: 921600

  on_boot:
    - tmc2209.setup:
        id: stepper_x
        microsteps: 16
        tcool_threshold: ${tcool_threshold_x}
        current: ${close_current_x}
        stall_threshold: ${open_stall_threshold_x}
        sense_resistor: ${sense_resistor}
        uart_address: ${tmc_address_x}
    - script.execute: 
        id: script_set_cover_open
        stepper_id: stepper_x

wifi:
  ssid: !secret wifi_ssid
  password: !secret wifi_password

# Enable logging
logger:
  level: INFO

# verbose logger over uart causes motor artifacts as pulses are generated in main loop
#logger:
#  level: VERBOSE
#  logs:
#    api: DEBUG
#    api.service: DEBUG
#    scheduler: DEBUG
#    stepper: DEBUG
#    uart: DEBUG

ota:
  password: "xxx"

uart:
  id: uart_stepper
  tx_pin: GPIO22
  rx_pin: GPIO21
  baud_rate: 9600

status_led:
  pin: GPIO26

api:
  encryption:
    key: "xxx"
  services:
    - service: control_stepper
      variables:
        stepper_id: string
        target: int
        speed: int
        microsteps: int
        tcool_threshold: int
        stall_threshold: int
        rms_current_amps: float
      then:
        - if:
            condition:
              lambda: 'return stepper_id == "stepper_x";'
            then:
              - tmc2209.setup:
                  id: stepper_x
                  microsteps: !lambda "return microsteps;"
                  tcool_threshold: !lambda "return tcool_threshold;"
                  stall_threshold: !lambda "return stall_threshold;"
                  current: !lambda "return rms_current_amps;"
                  sense_resistor: ${sense_resistor}
                  uart_address: ${tmc_address_x}
              - logger.log:
                  format: moving to %d
                  args: [target]
              - stepper.set_speed:
                  id: stepper_x
                  speed: !lambda "return speed;"
              - stepper.set_target:
                  id: stepper_x
                  target: !lambda "return target;"

    - service: set_cover_closed
      variables:
        stepper_id: string
      then:
        - script.execute: 
            id: script_set_cover_closed
            stepper_id: !lambda "return stepper_id;"
    - service: set_cover_open
      variables:
        stepper_id: string
      then:
        - script.execute: 
            id: script_set_cover_open
            stepper_id: !lambda "return stepper_id;"

    - service: close_variable_speed
      variables:
        stepper_id: string
        speed: int
        stall_threshold: int
      then:
        - if:
            condition:
              lambda:  'return stepper_id == "stepper_x";'
            then:
              - if:
                  condition:
                    and:
                      - binary_sensor.is_off: window_sensor
                      - binary_sensor.is_off: lower_limit_sensor
                  then:
                    - tmc2209.setup:
                        id: stepper_x
                        microsteps: 16
                        current: ${close_current_x}
                        stall_threshold: !lambda "return stall_threshold;"
                        sense_resistor: ${sense_resistor}
                        uart_address: ${tmc_address_x}
                    - stepper.set_speed:
                        id: stepper_x
                        speed: !lambda "return speed;"
                    - stepper.set_target:
                        id: stepper_x
                        target: 0
                    - wait_until:
                        condition:
                          lambda: |-
                            return id(stepper_x).current_position < 10;
                    - stepper.set_target:
                        id: stepper_x
                        target: ${back_off_steps}

    - service: open_variable_speed
      variables:
        stepper_id: string
        speed: int
        stall_threshold: int
      then:
        - if:
            condition:
              and:
                - binary_sensor.is_off: window_sensor
            then:
            - if:
                condition:
                  lambda:  'return stepper_id == "stepper_x";'
                then:
                - tmc2209.setup:
                    id: stepper_x
                    microsteps: 16
                    current: ${open_current_x}
                    stall_threshold: !lambda "return stall_threshold;"
                    sense_resistor: ${sense_resistor}
                    uart_address: ${tmc_address_x}
                - stepper.set_speed:
                    id: stepper_x
                    speed: !lambda "return speed;"
                - stepper.set_target:
                    id: stepper_x
                    target: !lambda "return id(open_position);"
                - wait_until:
                    condition:
                      lambda: |-
                        return id(stepper_x).current_position > (id(open_position)-10);
                - stepper.set_target:
                    id: stepper_x
                    target: !lambda "return id(open_position)-int(${back_off_steps});"

stepper:
  - platform: tmc2209
    steppers:
    - id: stepper_x
      step_pin: GPIO27
      dir_pin:
        number: GPIO26
        inverted: ${change_direction_x}
      sleep_pin:
        number: GPIO25
        inverted: true
      acceleration: ${acceleration}
      deceleration: ${acceleration}
      max_speed: ${velocity}
      sense_resistor: ${sense_resistor}
      uart_address: ${tmc_address_x}

binary_sensor:
  #   - platform: gpio
  #     name: Button1
  #     pin:
  #       number: GPIO23
  #       inverted: true
  #       mode: INPUT
  #     on_press:
  #       then:
  #         - cover.open:
  #             id: cover_x

  #   - platform: gpio
  #     name: Button2
  #     pin:
  #       number: GPIO34
  #       inverted: true
  #       mode: INPUT
  #     on_press:
  #       then:
  #         - cover.close:
  #             id: cover_x

  #   - platform: gpio
  #     name: Sensor1
  #     pin:
  #       number: GPIO22
  #       inverted: true
  #   - platform: gpio
  #     name: SensorGPIO0
  #     pin:
  #       number: GPIO0
  #       inverted: true
  #   - platform: gpio
  #     name: Sensor2
  #     pin:
  #       number: GPIO32
  #       inverted: true
  - platform: homeassistant
    name: "Window sensor homeassistant"
    entity_id: binary_sensor.lumi_lumi_sensor_magnet_aq2_2ad04f04_on_off
    id: window_sensor
    on_press:
      script.execute: 
        id: stop_at_current_position
        stepper_id: stepper_x
  - platform: gpio
    id: stall_guard_sensor
    name: StallGuard
    pin: GPIO34
    on_press:
      script.execute:
        id: stop_at_current_position
        stepper_id: stepper_x
  - platform: gpio # or use this pin as stall guard for y-axis
    id: lower_limit_sensor
    name: Lower Limit
    pin:
      number: GPIO35
      inverted: True
    on_press:
      if:
        condition:
          lambda: "return id(cover_x).current_operation == COVER_OPERATION_CLOSING;"
        then:
          - script.execute:
              id: stop_at_current_position
              stepper_id: stepper_x
          - script.execute:
              id: script_set_cover_closed
              stepper_id: stepper_x

script:
  - id: stop_at_current_position
    parameters:
      stepper_id: string
    then:
      - if:
          condition:
            lambda:  'return stepper_id == "stepper_x";'
          then:
            stepper.set_target:
              id: stepper_x
              target: !lambda "return id(stepper_x).current_position;"
  - id: script_set_cover_closed
    parameters:
      stepper_id: string
    then:
      - if:
          condition:
            lambda:  'return stepper_id == "stepper_x";'
          then:
            - stepper.report_position:
                id: stepper_x
                position: 0
            - stepper.set_target:
                id: stepper_x
                target: 0
                
  - id: script_set_cover_open
    parameters:
      stepper_id: string
    then:
      - if:
          condition:
            lambda:  'return stepper_id == "stepper_x";'
          then:
            - stepper.report_position:
                id: stepper_x
                position: !lambda "return id(open_position);"
            - stepper.set_target:
                id: stepper_x
                target: !lambda "return id(open_position);"

globals:
  - id: open_position
    type: float
    initial_value: "${distance_mm} / (${pulley_diameter_mm} * ${gear_ratio} * PI) * 200 * 16"

cover:
# X-COVER
  - platform: template
    id: cover_x
    name: "${device_name} cover X"
    has_position: True
    open_action:
      - if:
          condition:
            and:
              - binary_sensor.is_off: window_sensor
          then:
            - tmc2209.setup:
                id: stepper_x
                current: ${open_current_x}
                stall_threshold: ${open_stall_threshold_x}
                sense_resistor: ${sense_resistor}
                uart_address: ${tmc_address_x}
                microsteps: 16
            - stepper.set_speed:
                id: stepper_x
                speed: ${velocity}
            - stepper.set_target:
                id: stepper_x
                target: !lambda "return id(open_position);"
            - wait_until:
                condition:
                  lambda: |-
                    return id(stepper_x).current_position > (id(open_position)-10);
            - stepper.set_target:
                id: stepper_x
                target: !lambda "return id(open_position)-int(${back_off_steps});"
    close_action:
      - if:
          condition:
            and:
              - binary_sensor.is_off: window_sensor
              - binary_sensor.is_off: lower_limit_sensor
          then:
            - tmc2209.setup:
                id: stepper_x
                current: ${close_current_x}
                stall_threshold: ${close_stall_threshold_x}
                sense_resistor: ${sense_resistor}
                uart_address: ${tmc_address_x}
                microsteps: 16
            - stepper.set_speed:
                id: stepper_x
                speed: ${velocity}
            - stepper.set_target:
                id: stepper_x
                # 0 Means closed
                target: 0
            - wait_until:
                condition:
                  lambda: |-
                    return id(stepper_x).current_position < 10;
            - stepper.set_target:
                id: stepper_x
                target: ${back_off_steps}
    position_action:
      - if:
          condition:
            binary_sensor.is_off: window_sensor
          then:
            - tmc2209.setup:
                id: stepper_x
                current: ${open_current_x}
                stall_threshold: ${open_stall_threshold_x}
                sense_resistor: ${sense_resistor}
                uart_address: ${tmc_address_x}
                microsteps: 16
            - stepper.set_speed:
                id: stepper_x
                speed: ${velocity}
            - stepper.set_target:
                id: stepper_x
                target: !lambda "return id(open_position) * pos;"
    stop_action:
      - script.execute: 
          id: stop_at_current_position
          stepper_id: stepper_x

interval:
  - interval: 2s
    then:
      lambda: |-
        static auto operation = COVER_OPERATION_IDLE;
        static auto position = id(stepper_x).current_position;
        if (operation != id(cover_x).current_operation ||
            position != id(stepper_x).current_position)
        {
          if (id(stepper_x).current_position > id(stepper_x).target_position)
            operation = COVER_OPERATION_CLOSING;
          else if (id(stepper_x).current_position < id(stepper_x).target_position)
            operation = COVER_OPERATION_OPENING;
          else
            operation = COVER_OPERATION_IDLE;
          id(cover_x).current_operation = operation;

          position =  id(stepper_x).current_position;
          id(cover_x).position = position / id(open_position);

          id(cover_x).publish_state();

          ESP_LOGD("main", "Stepper X Position is: %d/%d", id(stepper_x).current_position, (int)id(open_position));
          // ESP_LOGD("main", "Stepper X Position is: %d/%d", id(stepper_x).current_position, (int)id(open_position));
          // ESP_LOGD("main", "Stepper X Position is: %d/%d", id(stepper_x).current_position, (int)id(open_position));
        }

Thanks! If I understand correctly, the adapted config isn't quite working yet for two steppers, or it's working but needs improvement? I'm looking to use it for basic features: open, close, stop. What's the stuff that's not working yet?

Thanks! If I understand correctly, the adapted config isn't quite working yet for two steppers, or it's working but needs improvement? I'm looking to use it for basic features: open, close, stop. What's the stuff that's not working yet?

Yes indeed, the uart communication specifically is not working correctly when using 2 or more steppers. You can probably make the bare minimum work without the uart configuration, but keep in mind you cant configure the current and microsteps of the tmc. Meaning defaults will be used, where current is maxed out and the microsteps are all over the place (because of how the pins are configured) x-Axis has 32 microsteps, y-axis 16, z-axis 8, and E-axis 64. Have a look at the a4988-component. Exchange the tmc2209 component with this one.

Ah I see. Thanks for elaborating. Unfortunately I don't have the experience to fix this. My blinds do require changing from the defaults, so I think I'll have to wait for now.

…

On Tue, May 23, 2023, 3:38 AM lumascet ***@***.***> wrote: ***@***.**** commented on this gist. ------------------------------ Thanks! If I understand correctly, the adapted config isn't quite working yet for two steppers, or it's working but needs improvement? I'm looking to use it for basic features: open, close, stop. What's the stuff that's not working yet? Yes indeed, the uart communication specifically is not working correctly when using 2 or more steppers. You can probably make the bare minimum work without the uart configuration, but keep in mind you cant configure the current and microsteps of the tmc. Meaning defaults will be used, where current is maxed out and the microsteps are all over the place (because of how the pins are configured) x-Axis has 32 microsteps, y-axis 16, z-axis 8, and E-axis 64. Have a look at the a4988-component <https://esphome.io/components/stepper/index.html?highlight=stepper#a4988-component>. Exchange the tmc2209 component with this one. — Reply to this email directly, view it on GitHub <https://gist.github.com/lumascet/d5a12a8ba942864726f4c34d10feba12#gistcomment-4576584> or unsubscribe <https://github.com/notifications/unsubscribe-auth/AF5HUZOVACQBP3Y7P7KXWDTXHRSOHBFKMF2HI4TJMJ2XIZLTSKBKK5TBNR2WLJDHNFZXJJDOMFWWLK3UNBZGKYLEL52HS4DFQKSXMYLMOVS2I5DSOVS2I3TBNVS3W5DIOJSWCZC7OBQXE5DJMNUXAYLOORPWCY3UNF3GS5DZVRZXKYTKMVRXIX3UPFYGLK2HNFZXIQ3PNVWWK3TUUZ2G64DJMNZZDAVEOR4XAZNEM5UXG5FFOZQWY5LFVEYTEMJYHA2DENRVU52HE2LHM5SXFJTDOJSWC5DF> . You are receiving this email because you commented on the thread. Triage notifications on the go with GitHub Mobile for iOS <https://apps.apple.com/app/apple-store/id1477376905?ct=notification-email&mt=8&pt=524675> or Android <https://play.google.com/store/apps/details?id=com.github.android&referrer=utm_campaign%3Dnotification-email%26utm_medium%3Demail%26utm_source%3Dgithub> .

Ah I see. Thanks for elaborating. Unfortunately I don't have the experience to fix this. My blinds do require changing from the defaults, so I think I'll have to wait for now.

I have searched around on Aliexpress looking for alternatives and I think I found another ESP32 based 3d printer board which should work without messing around on TMC uart: Makerbase MKS TinyBee 3D. With this board you can set the microsteps and current via switches and potentiometer. The pinout diagram can be found here .