Last active
May 29, 2025 17:54
-
-
Save mihaiserban/bf9aea36454fa2b1e724ab391cce053c to your computer and use it in GitHub Desktop.
Klipper Ender 5 Plus stock printer config
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| # This file contains pin mappings for the Creality Ender 5 Plus. | |
| # Ender 5 Plus stock uses a Creality v2.2 board, similar to CR-20 Pro. | |
| # To use this config, the firmware should be compiled for the AVR atmega2560. | |
| # See the example.cfg file for a description of available parameters. | |
| [stepper_x] | |
| step_pin: PF0 | |
| dir_pin: PF1 | |
| enable_pin: !PD7 | |
| step_distance: .0125 | |
| endstop_pin: ^PE5 | |
| position_endstop: 350 | |
| position_max: 350 | |
| homing_speed: 100 | |
| [stepper_y] | |
| step_pin: PF6 | |
| dir_pin: PF7 | |
| enable_pin: !PF2 | |
| step_distance: .0125 | |
| endstop_pin: ^PJ1 | |
| position_endstop: 350 | |
| position_max: 350 | |
| homing_speed: 100 | |
| [stepper_z] | |
| step_pin: PL3 | |
| dir_pin: PL1 | |
| enable_pin: !PK0 | |
| step_distance: .001266 | |
| #step_distance: .0025 | |
| endstop_pin: probe:z_virtual_endstop | |
| position_max: 400 | |
| position_min: -5 #set position_min to a negative value such as -5 when probing to set z offset, then revert to 0 | |
| homing_speed: 10.0 | |
| [extruder] | |
| step_pin: PA4 | |
| dir_pin: PA6 | |
| enable_pin: !PA2 | |
| step_distance: .010526 | |
| nozzle_diameter: 0.400 | |
| filament_diameter: 1.750 | |
| #pressure_advance: 0.617 # high value for stock long bowden tube, uncomment to enable pressure advance | |
| #pressure_advance_smooth_time: 0.010 # uncomment to enable pressure advance | |
| heater_pin: PB4 | |
| sensor_type: EPCOS 100K B57560G104F | |
| sensor_pin: PK5 | |
| control: pid | |
| pid_Kp: 22.2 | |
| pid_Ki: 1.08 | |
| pid_Kd: 114 | |
| min_temp: 0 | |
| max_temp: 260 | |
| [safe_z_home] | |
| home_xy_position: 180, 180 | |
| speed: 100 | |
| z_hop: 10 # Move up 10mm, so the probe doesnt hit anything | |
| z_hop_speed: 5 | |
| [bltouch] | |
| sensor_pin: ^PD3 | |
| control_pin: PB5 | |
| x_offset: -45 | |
| y_offset: 0 | |
| #z_offset: 0 | |
| speed: 3.0 | |
| samples: 1 | |
| pin_up_reports_not_triggered: True | |
| pin_up_touch_mode_reports_triggered: False | |
| [bed_mesh] | |
| speed: 100 | |
| horizontal_move_z: 8 | |
| mesh_min: 50, 50 | |
| mesh_max: 300,300 | |
| probe_count: 3,3 # 3,3 or 5,5 | |
| [gcode_macro G29] | |
| gcode: | |
| G28 | |
| BED_MESH_CALIBRATE | |
| BED_MESH_PROFILE SAVE=p1 | |
| G1 X0 Y0 Z5 F4000 | |
| [heater_bed] | |
| heater_pin: PH5 | |
| sensor_type: EPCOS 100K B57560G104F | |
| sensor_pin: PK6 | |
| control: pid | |
| pid_Kp: 690.34 | |
| pid_Ki: 111.47 | |
| pid_Kd: 1068.83 | |
| min_temp: 0 | |
| max_temp: 130 | |
| [fan] | |
| pin: PH6 | |
| [mcu] | |
| serial: /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_AK06VNAB-if00-port0 | |
| [printer] | |
| kinematics: cartesian | |
| max_velocity: 300 | |
| max_accel: 2000 # 20x print speed recommended | |
| max_z_velocity: 5 | |
| max_z_accel: 100 | |
| #[display] | |
| # Not sure this is supported for E5+ |
I was able to get klipper on my Ender 5 Plus stock v2.2 board without a pi, using elementary OS 7 directly to the Ender, the only problem i am having is the Z probe crashing into the bed....it starts way above the bed. I read that the Ender is opposite than klipper? I noticed when i am leveling Z when i hit a negative # the bed goes down positive # the bed goes up?
Anybody else have this issue?
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
@ssohail-droid Could be you need to change to whatever your pi is connected to
[mcu]
serial: /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_AK06VNAB-if00-port0